Spline Shaft Manufacturers in India
Spline Shafts made to your drawing or sample at our Gujarat unit, supplied across India and exported.
Asar Engineering Pvt. Ltd. Gandevi, Gujarat
- Teeth cut in-house: hobbing, shaping and spiral bevel cutting
- Induction hardening done in-house
- Made to your drawing or a worn sample
- Supplied across India and exported (IEC registered)
Involute and Straight-Sided Spline Shafts
Asar Engineering is a spline shaft manufacturer in India, making spline shafts to drawing at its unit in Gandevi, Gujarat, with the splines hobbed in-house. A spline shaft has several equally spaced teeth, or splines, cut along its length. These engage with a matching internally splined hub, sleeve, gear or coupling to transmit torque between the connected parts. Depending on the fit, the connection can be fixed or allow the hub to slide along the shaft.
A keyed shaft carries torque through a single key. A spline shaft shares it across several teeth around the circumference, which increases torque capacity for the same shaft size and avoids the stress concentration of a single deep keyway. We make each shaft to suit the spline profile, mating part, material, heat treatment and operating conditions of your equipment.
Spline shafts are used in industrial gearboxes, machine tools, hydraulic pumps and motors, agricultural machinery, construction equipment, cranes and vehicle drivetrains. Because they can transmit torque while allowing axial movement, they suit machines where parts must slide relative to one another in operation.
What is a Spline Shaft?
A spline shaft is a shaft with equally spaced ridges or teeth along its length, called splines. These fit into matching internal splines in a hub, sleeve, gear, coupling or other rotating part. The interlocking teeth transmit torque from the shaft to the connected part and, in sliding designs, allow controlled axial movement.
The main difference from a keyed shaft is how torque is carried. A keyed shaft uses one separate key fitted in keyways on the shaft and hub, so the load passes through a small contact area and the keyway raises stress in the shaft.
A spline shaft has the teeth formed on the shaft itself, so torque is carried by several teeth at once. This spreads the load more evenly around the shaft and gives greater torque capacity for the same shaft size.
Spline Shafts vs. Traditional Keyways
A keyed shaft has a single square or rectangular key fitted in keyways on the shaft and hub. This works for many drives, but the keyway is a cut-out in the shaft where stress concentrates.
A spline shaft avoids this with a series of interlocking teeth, so torque is spread over several contact areas instead of one key.
Key differences include:
- Load distribution: Multiple spline teeth distribute torque around the shaft circumference.
- Higher torque capability: The larger number of engaged teeth can support substantial torque transmission.
- Reduced localized stress: Load sharing can reduce the severe concentration associated with a single keyway.
- Axial movement: Sliding spline arrangements permit controlled axial movement while maintaining rotational engagement.
- Compact transmission: Splined connections can provide strong torque transfer without requiring a large external coupling arrangement.
- Accurate engagement: Properly manufactured spline profiles provide consistent contact between the shaft and mating component.
The actual torque capacity, service life, and allowable movement depend on spline geometry, material, dimensions, surface condition, fit, lubrication, loading, and operating environment.
Spline Profiles
Spline shafts are made with different tooth profiles, chosen for load, movement, accuracy and the mating part. The main profiles are straight-sided (parallel), involute and serrated. Ball splines are a separate, specialized design.
Parallel or Straight-Sided Splines
Straight-sided splines have teeth whose two flanks are parallel to each other, giving rectangular teeth. Sizes are standardized in ISO 14 and the equivalent Indian standard, which give light and medium series for a range of shaft diameters.
They are widely used for sliding gears and hubs, for example in machine tool gearboxes. With a suitable clearance fit, the hub slides freely along the shaft while staying locked in rotation.
The corners at the tooth roots concentrate stress, so root radius, dimensional accuracy, material and heat treatment are important for heavily loaded shafts.
Involute Splines
Involute splines have curved flanks with the same involute form as gear teeth, usually with a 30° pressure angle (37.5° and 45° are also used). They are standardized in ISO 4156, DIN 5480 and ANSI B92.1. The thicker tooth root gives lower stress concentration than straight-sided splines.
Under load, involute teeth tend to center the hub on the shaft. They can be hobbed like gears, which gives good accuracy and consistency.
They are the usual choice for heavily loaded drives where accurate engagement, torque capacity and durability matter.
Serrated or Triangular Splines
Serrated splines have many small triangular teeth, as in DIN 5481. Their fine pitch gives many engagement points around the shaft.
They are used for levers, clamping hubs and adjustable parts that must be fitted at many angular positions, and for compact, fixed torque connections.
Their suitability depends on tooth size, material, engagement length and torque. They are generally used for fixed connections rather than sliding ones.
Ball Splines
Ball splines have precision-ground grooves along the shaft that act as raceways for recirculating balls held in a mating spline nut. The rolling balls give very smooth, low-friction linear motion while still transmitting torque.
They are used in robotics, pick-and-place units and machine tools that need combined rotary and linear motion. Ball splines are specialized linear-motion products from dedicated makers and are different from conventional cut spline shafts.
Applications of Spline Shafts
Spline shafts are used across industry because they transmit torque and, where needed, allow controlled axial movement. The right design depends on torque, speed, axial travel, environment, space and required life.
Vehicle Drivetrains
Spline connections are widely used in vehicle drivetrains, including propeller shafts, gearbox output shafts, axle shafts and CV joints.
They keep parts locked in rotation while allowing axial movement as the suspension moves. Automotive OEM parts are made by specialist suppliers; spline shafts for industrial and off-highway machines can be made to drawing.
Machine Tools
Machine tool gearboxes use straight-sided or involute spline shafts carrying sliding gear clusters to change speeds, as well as splined feed and spindle drive shafts.
Accurate spline fit keeps the sliding gears moving freely without play.
Industrial Gearboxes
Industrial gearboxes use splines to connect shafts, gears and couplings. Splined shafts can be fixed or sliding depending on the gearbox design.
Hydraulic Pumps and Motors
Hydraulic pumps and motors use splined drive shafts to connect to the prime mover or gearbox, giving a compact, easily assembled connection.
Correct spline fit, surface finish, lubrication and accuracy keep wear low and engagement reliable.
Tractor PTO Systems
Tractors use splined Power Take-Off (PTO) shafts to drive implements such as rotavators, pumps, cutters and threshers.
Telescopic sliding splines in the PTO drive line accommodate changes in length as the implement moves.
Construction Equipment
Construction machinery uses splined shafts in hydraulic drives, transmissions, winches and swing drives, where high torque and reliable engagement are needed.
Cranes and Heavy Industrial Machinery
Cranes and heavy industrial machinery use splined shafts in gearboxes and drive assemblies, where torque must be transferred reliably under heavy duty.
Automation and Precision Machinery
Ball splines are used in automation systems that need combined rotary and linear movement, such as robots and pick-and-place units. Conventional spline shafts are used for indexing and transfer drives in special-purpose machines.
Common Types of Spline Shafts
Spline shafts can be classified by fit, movement and construction. Choosing the right type ensures proper torque transmission and a correct fit with the mating part.
Fixed Spline Shaft
A fixed spline shaft uses a close, transition or interference fit with its hub, and the hub is usually held axially by a shoulder, circlip or nut. The parts act as a solid rotating joint.
This suits connections where no axial movement is needed and the joint must stay rigid.
Sliding Spline Shaft
A sliding spline shaft allows the mating hub or sleeve to move axially along the shaft while maintaining rotational engagement.
This is used in sliding gear gearboxes, telescopic shafts, tractor PTO drive lines and machines where the distance between connected parts changes in operation.
Spline End Shaft
The spline is cut only on one or both ends of the shaft, for example to mount a coupling, gear or pump. This is the most common type in gearboxes and hydraulic drives.
Full-Length Spline Shaft
The spline runs along most of the shaft length so that gears or hubs can slide along it, as in machine tool speed gearboxes.
Spline Shaft with Integral Gear
The spline and a gear are cut on the same shaft, saving a separate hub and key. This is common in gearbox input and intermediate shafts.
Telescopic Spline Assembly
A spline shaft slides inside an internally splined tube or sleeve, allowing the drive line to change length while transmitting torque, as in PTO shafts and some drive shafts.
Core Components
A spline shaft assembly consists of several parts that decide its torque capacity, movement and performance.
Spline Shaft Body
The shaft body forms the main structural element and carries the spline teeth along its longitudinal surface. Its diameter, length, material, and overall geometry are selected according to the mechanical application.
Spline Teeth
Spline teeth are the raised sections distributed around the shaft circumference. Their profile, number, size, spacing, and engagement length influence torque transmission and mating compatibility.
Tooth Root
The tooth root is the transition area between adjacent spline teeth. Root geometry is important because it influences stress concentration and fatigue performance.
Mating Hub or Sleeve
The internally splined hub or sleeve has grooves that match the shaft teeth. It takes torque from the shaft while keeping the required fixed or sliding fit. Internal splines are usually cut by shaping or broaching.
Bore and Shaft Diameter
The shaft's main diameter and any bore through it decide its strength and how it fits the connected parts.
Key or Retaining Features
Depending on the shaft design, additional retaining features may be incorporated to position or secure mating components.
Flanges or Shoulders
Some spline shaft assemblies incorporate shoulders or flanged features to control the axial position of mating components.
Lubrication Interface
Sliding splines may require suitable lubrication between mating surfaces to reduce friction and wear. The lubrication method depends on the equipment and operating environment.
Spline Shaft Supplier in India
When choosing a spline shaft supplier in India, look beyond the shaft size. The supplier needs to know the torque, speed, axial movement, mating hub, material, environment and duty.
The key spline parameters are the standard or profile, number of teeth, module or size, engagement length, shaft diameter, fit class, material, heat treatment, surface finish and tolerances. Stating the standard (for example ISO 14, ISO 4156, DIN 5480 or ANSI B92.1) on the drawing avoids mismatch with the hub.
The fit between shaft and hub is especially important in sliding applications. Too much clearance causes play and wear; too little causes friction or stops the hub sliding. In fixed applications, the fit must hold the hub firmly without damaging the mating parts during assembly.
Material depends on the application. Carbon steels, alloy steels and stainless steels are chosen for strength, wear resistance and corrosion resistance. Splines can be induction hardened in-house for wear resistance.
Asar Engineering supplies spline shafts for gearboxes, machine tools, hydraulic systems, agricultural machinery, construction machinery and other power transmission equipment, from one-off replacements to batch orders.
Before dispatch, we check shaft diameters, spline dimensions over pins or with gauges, runout and key sizes with dial gauges against the drawing.
Benefits of Spline Shafts
Spline shafts provide several functional advantages in industrial power-transmission systems:
- Efficient torque transmission: Multiple teeth share the transmitted rotational load.
- Distributed loading: Torque is distributed around the shaft circumference instead of being concentrated through a single key.
- Reduced localized stress: The absence of one large keyway can reduce certain localized stress concentrations.
- Axial sliding capability: Sliding spline arrangements allow controlled movement while maintaining rotational engagement.
- Reliable rotational connection: Multiple interlocking teeth provide positive mechanical engagement.
- Compact construction: Splined connections can transmit substantial torque within a relatively compact mechanical arrangement.
- Angular positioning: Serrated splines allow parts to be fitted at many angular positions.
- Application flexibility: Different spline profiles and fits can be selected according to mechanical requirements.
- Suited to heavy machinery: Spline shafts are widely used in industrial gearboxes, machine tools, hydraulic, agricultural and construction equipment.
- Compatibility with specialized motion: Ball spline designs can combine rotary torque transmission with smooth linear movement.
Spline Shaft Specifications
| Specification | Typical Range / Consideration |
|---|---|
| Product Type | Spline Shaft |
| Spline Profile | Straight-sided (parallel), involute, serrated; ball splines are a separate specialized product |
| Configuration | Fixed or Sliding |
| Shaft Material | Carbon steel, alloy steel or stainless steel, selected for the application |
| Number of Splines | Application-dependent |
| Tooth Geometry | Profile selected according to mating component and load requirements |
| Shaft Diameter | As per mechanical design |
| Spline Length | Based on required engagement and axial movement |
| Overall Shaft Length | As per equipment requirements |
| Mating Component | Splined hub, sleeve, coupling, gear, or spline nut |
| Fit | Clearance (sliding); close, transition or interference (fixed) |
| Surface Finish | Selected according to movement, wear, and mating requirements |
| Heat Treatment | As required, e.g. induction hardening of splines |
| Axial Movement | Fixed or controlled sliding |
| Torque Transmission | Dependent on shaft diameter, spline geometry, material, and engagement |
| Operating Speed | Application-dependent |
| Lubrication | As required for sliding or high-load applications |
| Manufacturing Accuracy | To ISO 14, ISO 4156, DIN 5480, DIN 5481, ANSI B92.1 or customer drawing |
| Application | Gearboxes, machine tools, hydraulic pumps and motors, PTO drives, cranes, construction equipment |
| Customization | Dimensions, spline profile, material, fit, length, and other parameters can be application-specific |
Spline Shaft Exporter from India
Asar Engineering is IEC registered and takes export orders for spline shafts made to the customer's drawing. For export, the drawing, spline standard, material, surface condition and packing requirements must all be clear at the enquiry stage.
Spline shafts must mate with gears, couplings, hubs or hydraulic units at the destination, so the spline geometry must be reproduced exactly to the stated standard.
We quote against the full specification: shaft diameter, spline standard and size, number of teeth, spline length, overall length, material, heat treatment, surface finish, fit and any axial movement required.
Spline teeth and finished surfaces are protected against damage and corrosion for transit, with rust-preventive coating and suitable packing.
Why Choose Asar Engineering
- In-House Spline Cutting: External splines are hobbed and internal splines shaped at our unit in Gandevi, Gujarat.
- Made to Drawing or Sample: Spline shafts are made to your drawing or copied from a worn sample.
- Straight-Sided, Involute and Serrated Profiles: Made to the standard or profile your mating hub requires.
- Fixed and Sliding Fits: Fits are made for rigid connections or for hubs that must slide freely.
- Induction Hardening In-House: Splines can be induction hardened at our unit for wear resistance.
- Material Matched to the Application: Steel grade and hardness are chosen for torque, wear and environment.
- Inspection Before Dispatch: Diameters, spline dimensions and runout are checked with gauges before dispatch.
- One-Off to Batch, Across India and Export: From single replacements to batch orders, supplied across India and exported under our IEC registration.
This product is part of our industrial transmission gear range, made at our unit in Gujarat and supplied across India.
Related products: Gear Coupling, Helical Gear, Spur Gear, Spiral Bevel Gear, Worm Gear.
Get a Quote for Spline Shafts
Looking for a spline shaft manufacturer in India? Send your drawing or sample, the spline standard, the mating hub details and the quantity to Asar Engineering. We make spline shafts in Gujarat, supply across India and take export orders.
Get an accurate quote
What to Send for Your Spline Shaft Quote
- Drawing, sample or clear photos with main dimensions
- Module or DP, number of teeth and pressure angle
- Face width, bore size and keyway or spline details
- Material and hardness, if known
- Quantity and the date you need the parts
Have a drawing, a sample or a worn part?
Send it with the quantity. We reply with material, hardness, price and delivery time.
Industries That Use Our Spline Shafts
Material, hardness and fit are chosen for the duty the part will see in your plant.
-
Cement
Spline Shafts for kiln, mill, crusher and conveyor drives.
-
Steel & Metal
Spline Shafts for rolling mills and processing lines.
-
Sugar
Spline Shafts for cane carriers, mill drives and bagasse conveyors.
-
Mining & Material Handling
Spline Shafts for belt conveyors, crushers and bucket elevators.
-
Chemical & Process
Spline Shafts for pumps, mixers and agitators.
-
Machine Builders (OEM)
Spline Shafts for new machines, made to your drawing.
Our Spline Shafts and Recent Work
Photos of parts made and dispatched from our unit, not stock images.
Machining Videos from Our Shop Floor
Short, uncut clips of gear cutting, hobbing and machining at our unit in Gujarat.
What Our Customers Say
Reviews left on our Google Business Profile, shown word for word.
Asar Engineering supplied gearbox components for one of our industrial applications. The dimensional accuracy, finishing, and overall performance were satisfactory. We particularly appreciated their technical understanding and ability to suggest suitable solutions based on our operating requirements.
We have been sourcing industrial gearboxes from Asar Engineering Pvt. Ltd. and are satisfied with the product quality and consistency. The gearboxes are well-built, perform reliably under continuous operation, and were supplied according to our required specifications. Their team was also responsive during technical discussions and order coordination.
I bought a single screw extruder from asar engineering pvt.ltd. It's been a game changer for my manufacturing process. The extruder is efficient, easy to operate and built to last. Their customer is excellent and they guided me well through installation and setup. Highly recommended!
Spline Shaft FAQs
Questions buyers usually ask us before sending an enquiry for spline shaft.
Should my spline shaft be straight-sided, involute or serrated?
Straight-sided splines to ISO 14 are common for sliding gears in machine tool gearboxes. Involute splines, usually with a 30 degree pressure angle to ISO 4156, DIN 5480 or ANSI B92.1, have a stronger root and suit heavily loaded drives. Serrated splines to DIN 5481 suit fixed levers and clamping hubs. The profile must match your mating hub.
How do I choose between a fixed and a sliding spline fit?
A sliding spline shaft needs a clearance fit: too much clearance gives play and wear, too little makes the hub bind. A fixed joint uses a close, transition or interference fit, with the hub located by a shoulder, circlip or nut. Sliding splines also need lubrication, and induction hardening the splines improves wear life.
What should I include in a spline shaft enquiry?
Send the drawing or sample with the spline standard, number of teeth, module or size, fit class, spline length and overall length. Include shaft diameters, material, heat treatment, surface finish, any axial movement, the mating hub details and the quantity. Stating the spline standard on the drawing avoids a mismatch with the hub.
Can you copy a worn spline shaft, including one with an integral gear?
Yes. We make spline shafts from a worn sample or to drawing, including spline-end shafts, full-length splines and shafts with an integral gear. External splines are hobbed in-house and internal splines shaped, and splines can be induction hardened at our unit. Diameters, spline dimensions and runout are checked before dispatch.
Do you supply spline shafts in single quantities and for export?
Yes. We make spline shafts from a single replacement to batch orders at our unit in Gandevi, Gujarat, and supply across India. Export orders are accepted under our IEC registration and made to the stated spline standard, with splines and finished surfaces protected by rust-preventive coating and suitable packing for transit.
How We Make Your Spline Shafts
- Send your requirementDrawing, sample or photos of the spline shaft, with the quantity you need.
- Technical check and quoteWe confirm material, hardness and tolerances, then send price and delivery time.
- Manufacturing and inspectionMade at our Gandevi unit; dimensions are checked before dispatch.
- DispatchPacked for road transport across India, or for export shipment.
Companies We Supply
Need Spline Shafts made to your drawing?
Send the drawing or a sample with the quantity. We supply across India and take export orders.





























