Spiral Bevel Gear Manufacturers in India

Spiral Bevel Gears made to your drawing or sample at our Gujarat unit, supplied across India and exported.

Spiral Bevel Gear manufactured by Asar Engineering Pvt. Ltd.

Asar Engineering Pvt. Ltd. Gandevi, Gujarat

  • Teeth cut in-house: hobbing, shaping and spiral bevel cutting
  • Induction hardening done in-house
  • Made to your drawing or a worn sample
  • Supplied across India and exported (IEC registered)
Call +91-9898059219

Spiral Bevel Gear and Pinion Sets Cut In-House

Asar Engineering is a spiral bevel gear manufacturer in India. Spiral bevel teeth are cut in-house at our manufacturing unit in Gandevi, Gujarat, to the customer's drawing or sample. A spiral bevel gear is a conical gear with curved, oblique teeth that transmits power and torque between intersecting shafts, most commonly at 90 degrees. Unlike straight bevel teeth, which engage suddenly, the curved teeth enter and leave the mesh progressively. This reduces impact, vibration and noise, and suits higher speeds and loads.

We make each spiral bevel gear pair for its duty. Shaft arrangement, torque, speed, ratio, tooth geometry, material, heat treatment, lubrication and operating environment are all taken into account.

A spiral bevel gear pair normally consists of a smaller pinion, which usually drives, and a larger gear (often called the wheel or ring gear), which is driven. The curved teeth lie along the pitch cone and stay in progressive contact as the gears rotate, so the drive can be turned through a right angle while running smoothly.

When choosing a spiral bevel gear manufacturer in India, check whether the teeth are cut in-house, how the pair is matched and inspected for tooth contact and runout, what material and hardening are used, and whether the supplier understands your operating conditions.

What is a Spiral Bevel Gear?

A spiral bevel gear is a bevel gear with curved teeth cut on a cone-shaped blank. It transmits rotation and torque between intersecting shafts, most often at 90 degrees.

The spiral teeth engage gradually rather than all at once, as straight bevel teeth do. More than one pair of teeth shares the load at any moment (a higher contact ratio), so the force is spread out and rotation is smoother.

A spiral bevel gear pair is described by these elements:

  • Pinion: The smaller gear, usually the driver, which takes power from the input shaft.
  • Wheel (Ring Gear): The larger, driven gear, which takes motion and torque from the pinion.
  • Curved Tooth Profile: The teeth run across the face width at a defined spiral angle.
  • Pitch Cone: The conical reference surface from which the gear geometry is defined.
  • Intersecting Shafts: The shaft axes of pinion and wheel meet at a common point, the cone apex.

The two gears must be made as a matched pair. Their module, pressure angle and spiral angle must correspond, and the spiral hands are opposite: a left-hand pinion runs with a right-hand wheel, and vice versa.

Tooth Geometry

The curved tooth is the key feature of a spiral bevel gear. Contact starts at one end of the tooth and moves progressively across the face width, so the load is picked up gradually and impact between teeth is reduced. The contact pattern is kept slightly localised so that small deflections under load do not push it to the tooth edge.

Spiral Angle

The spiral angle is the angle between the tooth trace and the cone element (the line from the apex) at the middle of the face width. A mean spiral angle of about 35 degrees is common. It directly affects tooth overlap, load sharing, the axial thrust on the bearings and how smoothly the pair runs.

Pressure Angle

The pressure angle sets the direction of the force between mating teeth. 20 degrees is common. Both gears of the pair must have the same pressure angle.

Gear Ratio

The ratio is the number of teeth on the wheel divided by the number on the pinion. Choosing the ratio sets the output speed and torque: a higher ratio gives lower output speed and higher output torque.

Material and Heat Treatment

Under high torque or continuous duty, material selection and controlled heat treatment are important. Material properties affect tooth strength, wear resistance, fatigue life and service life.

Manufacturing Accuracy

Small errors in tooth geometry affect backlash, contact pattern, noise, vibration and load distribution. Accurate machining and inspection are therefore essential for spiral bevel gears.

Lubrication

Correct lubrication reduces friction and heat between mating teeth. The lubricant is chosen for the load, speed, temperature and gear material.

Applications of Spiral Bevel Gears

Spiral bevel gears are used where power must be transmitted between intersecting shafts with smooth, quiet running. Their curved teeth, load sharing and high efficiency suit many demanding industrial drives.

Common applications include:

  • Cement Plants: Conveyors, feeders, separators and other rotating equipment use spiral bevel gears where a right-angle drive is needed.
  • Mining Equipment: Conveyors, crushers and other heavy-duty mining machinery use spiral bevel gear drives under high loads and dusty conditions.
  • Steel Plants: Roller tables, conveyors and auxiliary drives in steel plants use spiral bevel gears where shafts intersect.
  • Industrial Gearboxes: Spiral bevel gear sets form the right-angle stage of bevel-helical gearboxes used in manufacturing and process plants.
  • Material Handling Equipment: Cranes, lifting machinery and conveyors use spiral bevel gears where the direction of the drive must change.
  • Machine Tools: Machine tools use spiral bevel gears where smooth, accurate right-angle motion is required.
  • Agricultural Machinery: Tractors, harvesters and farm processing machines use bevel gears to transfer power between shafts at an angle.
  • Pumps and Cooling Towers: Right-angle pump drives and cooling tower fan drives commonly use spiral bevel gears.
  • Sugar, Paper and Process Plants: Mills, conveyors, agitators and special machines use spiral bevel gears made to suit the power, speed and shaft arrangement.

Spiral Bevel Gears and Related Bevel Gear Types

Spiral bevel gears belong to the wider bevel gear family, which includes several tooth forms for different duties.

Spiral Bevel Gears

Spiral bevel gears have curved teeth at a defined spiral angle. Progressive engagement makes them run smoother than straight bevel gears, and they suit higher speeds, heavier loads and drives where noise and vibration must be low.

Straight Bevel Gears

Straight bevel gears have straight teeth that point towards the cone apex. They are simpler to make, but engagement is more sudden, especially at higher speeds.

Zerol Bevel Gears

Zerol bevel gears have curved teeth with a spiral angle of zero. They behave between straight and spiral bevel gears: some benefit of curved-tooth engagement, with thrust loads similar to straight bevel gears.

Hypoid Gears

Hypoid gears also have curved teeth, but the pinion axis is offset from the wheel axis, so the shafts do not intersect. The offset allows a larger, stronger pinion, and hypoid gears are widely used in vehicle axles. Because of the extra sliding between teeth, they need extreme-pressure (EP) gear oil.

Pinion and Ring Gear Pair

A spiral bevel drive runs as a matched pinion and wheel. The smaller pinion drives the larger wheel, with opposite spiral hands for correct meshing. If one gear of a worn pair is replaced, it is good practice to replace both.

Core Components of a Spiral Bevel Gear Drive

A spiral bevel gear drive consists of several components that work together to transmit power while keeping the gears correctly aligned.

Pinion

The pinion is the smaller gear of the pair and is usually the driver. It takes rotation from the input shaft and passes it to the larger gear.

Wheel (Ring Gear)

The wheel is the larger, driven gear. Its teeth mesh with the pinion and take the torque and rotation.

Gear Teeth

The curved teeth carry the load. Their geometry decides engagement, contact ratio, load distribution and running behaviour.

Gear Shaft

The shaft supports the gear and transfers rotational motion between the gear set and connected machinery. Shaft dimensions must be suitable for the expected torsional and bending loads.

Bearings

Bearings support the shafts and hold the pinion and wheel in position. Bearing selection is especially important because spiral bevel teeth produce both radial and axial (thrust) forces, and the thrust direction changes with the spiral hand and direction of rotation.

Gear Housing

The housing supports and protects the gear assembly and holds the components in position. It also contains the lubricant and keeps out contamination.

Lubrication System

Lubrication reduces friction, manages heat, limits wear, and protects tooth surfaces during operation. The lubrication method should correspond to the speed, load, temperature, and design of the gear assembly.

Seals

Seals help retain lubricant and reduce the entry of dust, moisture, and other contaminants. Proper sealing becomes particularly important in heavy industrial and outdoor applications.

Couplings

Couplings connect the gear drive to motors, shafts or driven equipment. Depending on the type, they can also take up limited misalignment.

Mounting Arrangement

Correct mounting keeps the pinion and wheel at their designed mounting distances. It is essential for the intended tooth contact pattern and to avoid early wear.

After installation, the tooth contact pattern is checked with marking compound. Under light load it should sit near the middle of the tooth, slightly towards the toe (small end), and spread along the face as load increases. The pinion mounting distance and backlash are adjusted until the pattern is correct.

Spiral Bevel Gear Supplier in India

As a spiral bevel gear supplier in India, we know that gear selection is not based on nominal power alone. Speed, torque, duty cycle, shock loading, shaft orientation, ratio, lubrication, temperature, mounting and running hours all affect the design.

Asar Engineering supplies spiral bevel gear pairs as new parts, as replacements for existing gearboxes and machines, and to customer drawings. We look at the machine and its working environment before recommending material and hardening.

When evaluating a spiral bevel gear supplier, consider:

  • Manufacturing and engineering capability
  • Tooth geometry and machining accuracy
  • Material selection
  • Heat-treatment practices
  • Gear tooth surface quality
  • Dimensional inspection
  • Spiral angle accuracy
  • Pressure-angle consistency
  • Load and torque requirements
  • Gear ratio requirements
  • Lubrication arrangements
  • Quality-control procedures
  • Customization capability
  • Technical assistance
  • Delivery coordination

A good supplier also separates standard needs from application-specific ones. High-speed drives need tooth accuracy, balancing, surface finish, lubrication and vibration control. Heavy-duty drives need tooth strength, the right material, heat treatment and load capacity.

If you are replacing a worn spiral bevel pair and have no drawing, send both gears. We measure the tooth counts, module, spiral angle and hand, pressure angle, cone distance and mounting dimensions from the sample and make a matched pair. Tell us the machine, motor power and speed so that we can check the material and hardening.

Benefits of Spiral Bevel Gears

  • Higher Load Capacity: Progressive engagement spreads the load over more than one tooth at a time, so spiral bevel gears carry more torque than straight bevel gears of the same size.
  • Smooth Operation: Curved teeth enter the mesh gradually instead of all at once, as in straight bevel gears.
  • Reduced Noise and Vibration: Gradual engagement reduces tooth impact, especially at higher speeds.
  • High-Speed Capability: Spiral bevel gears suit higher pitch-line speeds than straight bevel gears.
  • Efficient Power Transmission: Well-made and lubricated spiral bevel gears transmit power between intersecting shafts with low losses.
  • Change of Direction: Spiral bevel gears turn the drive through the shaft angle, commonly 90 degrees.
  • Compact Right-Angle Drive: The conical arrangement turns the drive without long or complicated shaft layouts.
  • Suitable for Heavy-Duty Machinery: Correctly designed spiral bevel gears are used in mining, cement, steel and other heavy engineering equipment.
  • Reliable Performance: Accurate cutting, the right material, heat treatment, lubrication and correct installation give dependable service.
  • Long Service Life: Run within their design limits, with correct lubrication and alignment, spiral bevel gears give long service.
  • Application Flexibility: Ratio, shaft arrangement, speed, torque, material and mounting can all be designed to suit the machine.

Spiral Bevel Gear Specifications

Technical ParameterTypical RangeDescription
Gear TypeSpiral BevelCurved-tooth bevel gear for intersecting shafts
Gear ArrangementPinion and wheel (ring gear)Matched driving and driven gear pair
Shaft ArrangementCommonly 90° intersecting shaftsUsed to turn the drive through an angle
Tooth ProfileCurved / SpiralProvides progressive tooth engagement
Spiral DirectionLeft-hand or Right-handMating gears have opposite spiral hands
Pressure AngleCommonly 20°Selected according to gear design requirements
Spiral AngleCommonly about 35° (mean spiral angle)Influences tooth overlap, smoothness and axial thrust
Gear RatioApplication dependentWheel teeth divided by pinion teeth
MaterialAlloy steel, e.g. 20MnCr5, EN353 (case-hardening) or EN19, EN24 (through-hardening)Selected according to load, speed, wear, and service requirements
Heat TreatmentInduction hardening; case carburising where specifiedMay be used to improve tooth strength and wear resistance
LubricationGear oil; EP gear oil for heavy loadsSelected according to speed, load, temperature, and gear design
Manufacturing AccuracyApplication dependentInfluences tooth contact, backlash, noise, and vibration
Operating SpeedApplication dependentDetermined by gear geometry, material, lubrication, and system design
Torque CapacityApplication dependentDetermined through engineering calculations and operating conditions
MountingApplication dependentMust hold the correct mounting distance and alignment of pinion and wheel

Actual limits, dimensions, materials, ratio, tooth geometry, speed, torque capacity and lubrication must be confirmed for each gear design by calculation.

Spiral Bevel Gear Exporter from India

Asar Engineering is a spiral bevel gear exporter from India and is registered with an IEC (Importer-Exporter Code). We take export orders for gears made to drawing for heavy engineering, material handling, mining, cement, steel and power transmission equipment.

Export orders need attention to dimensions, packaging, documentation, inspection, material certificates and delivery planning, especially when gears are made to a specific drawing or specification.

Spiral bevel gears for export can be made to requirements such as:

  • Gear diameter
  • Number of teeth
  • Gear ratio
  • Spiral angle
  • Pressure angle
  • Shaft arrangement
  • Input speed
  • Output speed
  • Transmitted torque
  • Material
  • Heat treatment
  • Tooth accuracy
  • Lubrication requirements
  • Mounting configuration

Complete application details help us understand the operating conditions and make a gear that suits the machine.

With an enquiry, please send the drawing or sample, the number of teeth on pinion and wheel, shaft angle, spiral hand, motor power and speed, and the quantity required.

Why Choose Asar Engineering

  • In-House Spiral Bevel Gear Cutting: Spiral bevel teeth are cut in-house at our unit in Gujarat.
  • Made to Drawing or Sample: We manufacture to your drawing or from a worn sample, from one-off replacement pairs to batch orders.
  • Induction Hardening In-House: Teeth can be induction hardened in our own facility for wear resistance.
  • Material Matched to the Application: Material and hardness are selected according to load, speed and operating environment.
  • Inspection Before Dispatch: Dimensions and runout are checked with dial gauges before every gear pair is dispatched.
  • Technical Support: You can discuss your torque, speed, shaft arrangement and operating conditions with our team before ordering.
  • Supply Across India and Export: We supply customers across India and take export orders as an IEC-registered company.

This product is part of our industrial transmission gear range, made at our unit in Gujarat and supplied across India.

Related products: Gear Coupling, Industrial Gearbox, Helical Gear.

Get Spiral Bevel Gears Made to Your Drawing

Send us your drawing or sample, the quantity you need and details of your application, and we will quote. Asar Engineering supplies spiral bevel gears across India and takes export orders.

Get an accurate quote

What to Send for Your Spiral Bevel Gear Quote

  • Drawing, sample or clear photos with main dimensions
  • Module or DP, number of teeth and pressure angle
  • Face width, bore size and keyway or spline details
  • Material and hardness, if known
  • Quantity and the date you need the parts

Have a drawing, a sample or a worn part?

Send it with the quantity. We reply with material, hardness, price and delivery time.

or call +91-9898059219
Industries

Industries That Use Our Spiral Bevel Gears

Material, hardness and fit are chosen for the duty the part will see in your plant.

  • Cement

    Spiral Bevel Gears for kiln, mill, crusher and conveyor drives.

  • Steel & Metal

    Spiral Bevel Gears for rolling mills and processing lines.

  • Sugar

    Spiral Bevel Gears for cane carriers, mill drives and bagasse conveyors.

  • Mining & Material Handling

    Spiral Bevel Gears for belt conveyors, crushers and bucket elevators.

  • Chemical & Process

    Spiral Bevel Gears for pumps, mixers and agitators.

  • Machine Builders (OEM)

    Spiral Bevel Gears for new machines, made to your drawing.

Real photos

Our Spiral Bevel Gears and Recent Work

Photos of parts made and dispatched from our unit, not stock images.

View all photos
Spiral bevel gear
Spiral bevel gear
Batch of spiral bevel gears
Batch of spiral bevel gears
Spiral bevel pinion shafts
Spiral bevel pinion shafts
Spiral bevel gear sets
Spiral bevel gear sets
Gear shaping machine at our Gandevi unit
Gear shaping machine at our Gandevi unit
Internal gear being shaped on a gear shaper
Internal gear being shaped on a gear shaper
Pinion gear teeth being shaped
Pinion gear teeth being shaped
Herringbone gear
Herringbone gear
Customer feedback

What Our Customers Say

Reviews left on our Google Business Profile, shown word for word.

View more reviews on Google
★★★★★
Asar Engineering supplied gearbox components for one of our industrial applications. The dimensional accuracy, finishing, and overall performance were satisfactory. We particularly appreciated their technical understanding and ability to suggest suitable solutions based on our operating requirements.
Amit Kulkarni
★★★★
We have been sourcing industrial gearboxes from Asar Engineering Pvt. Ltd. and are satisfied with the product quality and consistency. The gearboxes are well-built, perform reliably under continuous operation, and were supplied according to our required specifications. Their team was also responsive during technical discussions and order coordination.
Rajesh M
★★★★★
I bought a single screw extruder from asar engineering pvt.ltd. It's been a game changer for my manufacturing process. The extruder is efficient, easy to operate and built to last. Their customer is excellent and they guided me well through installation and setup. Highly recommended!
NEERAJ CHAUDHARY (NK)
FAQ

Spiral Bevel Gear FAQs

Questions buyers usually ask us before sending an enquiry for spiral bevel gear.

When is a spiral bevel gear a better choice than a straight bevel gear?

Choose a spiral bevel gear when the right-angle drive runs at higher speed or load, or when noise and vibration must stay low. The curved teeth take up load progressively with more than one tooth in contact, so the pair carries more torque than a straight bevel set of the same size. The trade-off is higher axial thrust on the bearings.

What spiral angle, pressure angle and material do you typically use?

A mean spiral angle of about 35 degrees and a 20 degree pressure angle are common, though the final values follow your drawing and duty. Typical spiral bevel gear materials are case-hardening 20MnCr5 or EN353, or through-hardening EN19 and EN24. We induction harden teeth in-house, with carburising where your specification calls for it. EP gear oil suits heavily loaded sets.

What information do you need to quote a spiral bevel gear pair?

Send the drawing or the worn pair, the tooth counts of pinion and wheel, shaft angle, spiral hand, module and mounting dimensions. Also state the motor power, input speed, the machine it drives and the quantity required. With these details we can check material and hardening against the load before we quote.

Can you replace only the pinion of a worn spiral bevel gear set?

We recommend replacing both gears. A spiral bevel pinion and wheel are cut as a matched pair with opposite spiral hands, and a new pinion running on a worn wheel rarely gives a correct contact pattern. Send both gears and we will measure tooth counts, module, spiral angle and hand, pressure angle and mounting distances to make a new matched set.

How do you handle spiral bevel gear orders from other states or abroad?

We make the gears at our unit in Gandevi, Gujarat, and supply them across India. Export orders are accepted under our IEC registration and made to the buyer's drawing and standard. Every pair has its dimensions and runout checked with dial gauges before dispatch, and we accept single replacement pairs as well as batch orders.

How to order

How We Make Your Spiral Bevel Gears

  1. Send your requirementDrawing, sample or photos of the spiral bevel gear, with the quantity you need.
  2. Technical check and quoteWe confirm material, hardness and tolerances, then send price and delivery time.
  3. Manufacturing and inspectionMade at our Gandevi unit; dimensions are checked before dispatch.
  4. DispatchPacked for road transport across India, or for export shipment.
Clients

Companies We Supply

Avgol logo
Eveready logo
Akash logo
Santec Group logo
Linit Exports Pvt Ltd logo
Lasons logo
Maredo logo
Hardcarb logo
PAA logo
Prochem logo
Orange logo
ACE Robotics Pvt Ltd logo
Castco logo
BHARAT FORGE logo
Kalyani logo
ARV Engineering logo
Coromandel logo
Bioradmedisys logo
Al tamauez logo
Murugappa logo
Gansons logo
Emami Agrotech Ltd logo
GSW logo
Godrej logo
JSW logo
Bhushan Power & Steel logo
Unicare logo
Centuryply logo
Exide logo
Ha-KO Industries logo

Need Spiral Bevel Gears made to your drawing?

Send the drawing or a sample with the quantity. We supply across India and take export orders.

Call +91-9898059219