Hypoid Gear Manufacturers in India

Hypoid Gears made to your drawing or sample at our Gujarat unit, supplied across India and exported.

Hypoid Gear manufactured by Asar Engineering Pvt. Ltd.

Asar Engineering Pvt. Ltd. Gandevi, Gujarat

  • Teeth cut in-house: hobbing, shaping and spiral bevel cutting
  • Induction hardening done in-house
  • Made to your drawing or a worn sample
  • Supplied across India and exported (IEC registered)
Call +91-9898059219

Hypoid Gears for Offset Right-Angle Drives

Asar Engineering is a hypoid gear manufacturer in India, with its manufacturing unit at Gandevi, Gujarat, where we also cut spiral bevel gears in-house. We make hypoid gear sets for industrial right-angle drives to the customer's drawing or sample. A hypoid gear is a special form of spiral bevel gear that transmits power between non-intersecting, non-parallel shafts, usually at 90 degrees. Its defining feature is the axis offset: the pinion axis sits above or below the axis of the larger gear (the ring gear or wheel) instead of passing through it.

This offset is what distinguishes hypoid gears from spiral bevel gears. It lets the pinion be larger and stronger for the same ratio and wheel size. The result is high torque capacity, smooth running, a compact layout and a large tooth contact area.

Spiral bevel teeth work mainly by rolling contact. Hypoid teeth combine rolling with a large amount of sliding along the tooth length. The high contact ratio makes hypoid gears quiet, but the sliding produces extra friction and heat, so efficiency is somewhat lower than for spiral bevel gears and correct lubrication is essential.

Each hypoid gear set is designed around axis offset, ratio, torque, speed, tooth geometry, material, heat treatment, lubrication, mounting and operating environment.

When choosing a hypoid gear manufacturer in India, check how the pinion and wheel are cut and matched, how tooth contact is checked, what material and hardening are used, and whether the supplier understands the lubrication hypoid gears need.

What is a Hypoid Gear?

A hypoid gear belongs to the spiral bevel gear family but is used on offset, non-intersecting shafts. The axes of the two gears do not meet; the pinion axis is offset from the axis of the wheel.

The axis offset is the signature feature of a hypoid gear set. The position of the pinion relative to the wheel gives layout and strength advantages that are hard to get with an intersecting-axis bevel gear.

A hypoid gear set is described by these elements:

  • Hypoid Pinion: The smaller gear, usually the driver, which takes power from the input shaft.
  • Hypoid Wheel (Ring Gear): The larger, driven gear, which takes rotation and torque from the pinion.
  • Axis Offset: The distance between the pinion axis and the wheel axis.
  • Spiral Tooth Geometry: Curved teeth that engage progressively.
  • Offset Shaft Arrangement: The input and output axes do not intersect, but the drive still turns through a right angle.

The offset allows a larger pinion diameter than a spiral bevel pinion for the same ratio. This gives higher tooth strength and load capacity.

Axis Offset

The axis offset is the distance by which the pinion axis sits above or below the wheel axis. It is the main design parameter of a hypoid gear set.

The offset also helps the machine layout. In vehicle axles, for example, a lower pinion lets the drive shaft run lower.

Hyperboloid Gear Geometry

The name 'hypoid' comes from hyperboloid: the theoretical pitch surfaces of a hypoid pair are hyperboloids, not the simple cones of bevel gears. In practice the gears are made on conical blanks, and the tooth surfaces are generated to suit the offset between the shafts.

This geometry gives a large tooth contact while transmitting power between non-intersecting axes.

Rolling and Sliding Contact

Hypoid teeth work with a combination of rolling and sliding contact. The sliding is much greater than in spiral bevel gears and increases with the offset.

The sliding causes extra friction and heat, and the tooth surfaces are at risk of scoring. Correct lubrication is therefore essential.

Pinion Size

The offset allows the hypoid pinion to be larger than the pinion of a spiral bevel pair of the same ratio. A larger pinion has stronger teeth and carries more load.

Gear Ratio

The ratio is the number of teeth on the wheel divided by the number on the pinion. A hypoid set reduces speed and increases output torque according to this ratio.

Lubrication Requirement

Because of the high sliding between hypoid teeth, they need extreme-pressure (EP) gear oil. Hypoid gear oils of API GL-5 grade are commonly used; normal gear oil without EP additives can lead to scoring.

A new hypoid gear set should be run in at reduced load for the first hours of operation, and the oil changed after running-in to remove wear particles. Oil level and condition should then be checked at regular intervals.

Applications of Hypoid Gears

Hypoid gears are used where high torque, smooth running, a compact layout and an offset right-angle drive are needed. Their best-known use is the rear axle of cars and trucks; in industry they are used in right-angle speed reducers and heavy drives.

Common applications include:

  • Industrial Gearboxes: Hypoid gear sets are used in compact right-angle speed reducers that drive high-load machines.
  • Right-Angle Speed Reducers: The offset shafts suit compact drives that must change the direction of power.
  • Material Handling Equipment: Heavy material handling machinery uses hypoid gears where high torque and a compact right-angle drive are needed.
  • Conveyor Drives: Conveyors use hypoid gear reducers for compact, reliable right-angle drives.
  • Industrial Machinery: Machines needing high torque, low noise and an offset shaft position use hypoid gear drives.
  • Special Power Transmission Equipment: Hypoid gears are used where intersecting-axis bevel gears cannot give the required layout or load capacity.

The right hypoid gear design depends on torque, speed, ratio, axis offset, tooth geometry, lubrication, load, operating temperature and available space.

Common Types of Hypoid Gear Arrangements

Hypoid gears can be grouped by where they are used and how the drive is arranged.

Hypoid Gears in Vehicle Axles

The most common use of hypoid gears is the final drive of vehicle axles, where the offset lets the drive shaft sit lower relative to the axle centreline while carrying high torque.

Industrial Hypoid Gears

Industrial hypoid gears are used in gearboxes and speed reducers that need high torque, compact size, quiet running and offset shafts.

They are used in material handling, conveyors, lifting machinery and other industrial drives.

Right-Angle Hypoid Gearboxes

Right-angle hypoid gearboxes use a hypoid gear set to turn the drive through 90 degrees, with an offset between the input and output shaft axes.

This gives a compact alternative to other right-angle drives, and a higher efficiency than a worm drive of similar ratio.

Compared with a worm drive, a hypoid drive has lower sliding losses and runs cooler at the same ratio. Compared with a spiral bevel drive, it gives a stronger pinion and more freedom in shaft layout, at the cost of more sliding and the need for EP oil.

Offset Pinion Hypoid Gears

The pinion is placed above or below the wheel axis. The amount and direction of the offset are important design parameters that affect layout, tooth geometry, contact conditions and performance.

Core Components of a Hypoid Gear Drive

A hypoid gear drive consists of several components that work together to transmit power through an offset shaft arrangement.

Hypoid Pinion

The hypoid pinion is the driving gear that takes power from the input shaft. Its geometry is designed to mesh with the offset wheel.

For the same ratio, a hypoid pinion can be larger than a spiral bevel pinion, which gives higher load capacity.

Hypoid Wheel (Ring Gear)

The wheel is the larger, driven gear of the set. Its curved teeth mesh with the pinion and take the torque.

Spiral Tooth Profile

The curved teeth engage progressively. Their geometry must be cut accurately, and the pinion and wheel are made and supplied as a matched set to get the correct contact pattern.

The contact pattern is checked with marking compound during assembly. The pinion mounting distance and backlash are adjusted until the pattern sits correctly on both the drive and coast sides of the teeth.

Axis Offset

The axis offset is the defining feature of the hypoid gear set: the distance between the pinion and wheel axes.

Gear Shaft

The shafts transmit rotation between the gear set and the connected machinery. Their size and material must suit the torsional, bending and operating loads.

Bearings

Bearings support the shafts and hold the gears in alignment. Correct bearing selection is important because hypoid gears produce high axial and radial forces, especially on the pinion.

Gear Housing

The housing supports the gear set and bearings, holds the alignment and contains the lubricant.

It also protects internal components from dust, moisture, and other contaminants.

Lubrication System

Lubrication is especially important for hypoid gears because of their high sliding. A suitable extreme-pressure lubricant protects the teeth against scoring and wear.

Seals

Seals keep the lubricant in and dust and moisture out. Good sealing is essential in heavy industrial environments.

Hypoid Gear Supplier in India

Asar Engineering is a hypoid gear supplier in India for industrial right-angle drives in material handling, conveyors, lifting machinery and general engineering, including replacement gear sets made to drawing or sample.

A good supplier understands the special geometry and lubrication needs of hypoid gears. Because of the high sliding contact, gear design and lubricant selection must be decided together.

We select the gear set for each machine based on torque, speed, ratio, axis offset, operating temperature and installation conditions.

When evaluating a hypoid gear supplier, consider:

  • Manufacturing and engineering capabilities
  • Hypoid tooth geometry
  • Axis-offset accuracy
  • Pinion and wheel matching
  • Material selection
  • Heat-treatment practices
  • Tooth-contact inspection
  • Gear ratio requirements
  • Torque capacity
  • Operating speed
  • Lubrication compatibility
  • Extreme-pressure oil requirements
  • Dimensional accuracy
  • Quality inspection procedures
  • Customization capabilities
  • Technical support
  • Delivery coordination

Hypoid gear performance depends heavily on tooth geometry, mounting accuracy, bearing support, lubrication and operating conditions, so a supplier should look at all of them together.

If you are replacing a worn hypoid set and have no drawing, send both gears. The pinion and wheel must be measured together, including tooth counts, offset, spiral angle and hand, and mounting distances, because a hypoid pinion only runs correctly with its own matched wheel.

Benefits of Hypoid Gears

  • High Torque Capacity: A larger pinion and a large tooth contact area let hypoid gears carry high loads.
  • Strong Pinion: The offset permits a larger pinion than a comparable spiral bevel pair, giving stronger teeth.
  • Smooth Operation: Curved teeth engage progressively and more teeth are in contact at a time.
  • Low Noise: Hypoid gear sets run quietly, which is why they are used where gear noise matters.
  • Compact Layout: The offset gives more freedom in positioning the drive in a limited space.
  • Right-Angle Power Transmission: Hypoid gears turn the drive through about 90 degrees with non-intersecting shafts.
  • Reliable Power Transfer: Correctly made, aligned, lubricated and maintained hypoid gear sets give dependable service.
  • Application Flexibility: Hypoid gears are used in industrial gearboxes, conveyors, lifting systems and heavy machinery.
  • Reduced Vibration: Progressive engagement and controlled tooth contact give smoother running.
  • Efficient Torque Multiplication: The ratio reduces input speed and increases output torque, with better efficiency than a worm drive of similar ratio.

Hypoid Gear Specifications

Technical ParameterTypical RangeDescription
Gear TypeHypoid (offset spiral bevel)Spiral bevel gear with offset axes
Shaft ArrangementNon-intersecting / OffsetInput and output axes do not meet
Shaft DirectionCommonly 90°Provides directional power transmission
Pinion TypeHypoid PinionOffset driving component
Driven GearHypoid wheel (ring gear)Larger driven component
Axis OffsetApplication dependentDistance between pinion and wheel axes
Tooth ProfileCurved / Hypoid SpiralDesigned for progressive rolling and sliding contact
Gear RatioApplication dependentWheel teeth divided by pinion teeth
Pressure AngleApplication dependentSelected according to gear design
Spiral GeometryApplication dependentInfluences contact and load transmission
MaterialCase-hardening alloy steel, e.g. 20MnCr5, EN353Selected according to load and operating conditions
Heat TreatmentCase carburising and hardening (typical for hypoid gears)Gives a hard, wear-resistant tooth surface with a tough core
Operating SpeedApplication dependentDetermined by gear design and lubrication
Torque CapacityApplication dependentDetermined through engineering calculations
LubricationHypoid / EP gear oil (API GL-5 type)Protects the teeth against scoring from high sliding
Bearing ArrangementRadial and thrust-carrying (e.g. taper roller)Selected according to transmitted gear forces
HousingCast / Fabricated / Application dependentSupports and protects the gear assembly

Actual dimensions, axis offset, ratio, tooth geometry, speed, torque capacity, material, heat treatment, lubricant grade and operating limits must be confirmed for each hypoid gear design by calculation.

Hypoid Gear Exporter from India

Asar Engineering is a hypoid gear exporter from India and is registered with an IEC (Importer-Exporter Code). Export orders are made to the customer's drawing, with torque, speed, ratio, axis offset, operating temperature and mounting taken into account.

Hypoid gears for export can be made to requirements such as:

  • Pinion dimensions
  • Wheel dimensions
  • Number of teeth
  • Gear ratio
  • Axis offset
  • Pressure angle
  • Spiral geometry
  • Input speed
  • Output speed
  • Transmitted torque
  • Material
  • Heat treatment
  • Tooth-contact pattern
  • Lubrication requirements
  • Mounting arrangement

Complete machine details help us check the required hypoid geometry and make a gear set that suits the operating conditions.

Why Choose Asar Engineering

  • In-House Spiral Bevel Gear Cutting: Curved-tooth bevel gears are cut in-house at our unit in Gandevi, Gujarat.
  • Made to Drawing or Sample: We manufacture to your drawing or from a worn sample, from one-off replacement sets to batch orders.
  • Induction Hardening In-House: Teeth can be induction hardened in our own facility where the application suits it.
  • Material Matched to the Application: Material and hardness are selected according to torque, speed and operating conditions.
  • Inspection Before Dispatch: Dimensions and runout are checked with dial gauges before every gear set is dispatched.
  • Lubrication Advice: We advise on the extreme-pressure lubrication that hypoid gears need.
  • Technical Support: You can discuss torque, speed, axis offset, ratio and mounting with our team before ordering.
  • Supply Across India and Export: We supply customers across India and take export orders as an IEC-registered company.

This product is part of our industrial transmission gear range, made at our unit in Gujarat and supplied across India.

Related products: Gear Coupling, Helical Gear, Spur Gear.

Get Hypoid Gears Made to Your Drawing

Send us your drawing or sample, the quantity you need and details of your application, and we will quote. Asar Engineering supplies hypoid gears across India and takes export orders.

Get an accurate quote

What to Send for Your Hypoid Gear Quote

  • Drawing, sample or clear photos with main dimensions
  • Module or DP, number of teeth and pressure angle
  • Face width, bore size and keyway or spline details
  • Material and hardness, if known
  • Quantity and the date you need the parts

Have a drawing, a sample or a worn part?

Send it with the quantity. We reply with material, hardness, price and delivery time.

or call +91-9898059219
Industries

Industries That Use Our Hypoid Gears

Material, hardness and fit are chosen for the duty the part will see in your plant.

  • Cement

    Hypoid Gears for kiln, mill, crusher and conveyor drives.

  • Steel & Metal

    Hypoid Gears for rolling mills and processing lines.

  • Sugar

    Hypoid Gears for cane carriers, mill drives and bagasse conveyors.

  • Mining & Material Handling

    Hypoid Gears for belt conveyors, crushers and bucket elevators.

  • Chemical & Process

    Hypoid Gears for pumps, mixers and agitators.

  • Machine Builders (OEM)

    Hypoid Gears for new machines, made to your drawing.

Real photos

Our Hypoid Gears and Recent Work

Photos of parts made and dispatched from our unit, not stock images.

View all photos
Spiral bevel gear
Spiral bevel gear
Batch of spiral bevel gears
Batch of spiral bevel gears
Spiral bevel pinion shafts
Spiral bevel pinion shafts
Spiral bevel gear sets
Spiral bevel gear sets
Gear shaping machine at our Gandevi unit
Gear shaping machine at our Gandevi unit
Internal gear being shaped on a gear shaper
Internal gear being shaped on a gear shaper
Pinion gear teeth being shaped
Pinion gear teeth being shaped
Herringbone gear
Herringbone gear
Customer feedback

What Our Customers Say

Reviews left on our Google Business Profile, shown word for word.

View more reviews on Google
★★★★★
Asar Engineering supplied gearbox components for one of our industrial applications. The dimensional accuracy, finishing, and overall performance were satisfactory. We particularly appreciated their technical understanding and ability to suggest suitable solutions based on our operating requirements.
Amit Kulkarni
★★★★
We have been sourcing industrial gearboxes from Asar Engineering Pvt. Ltd. and are satisfied with the product quality and consistency. The gearboxes are well-built, perform reliably under continuous operation, and were supplied according to our required specifications. Their team was also responsive during technical discussions and order coordination.
Rajesh M
★★★★★
I bought a single screw extruder from asar engineering pvt.ltd. It's been a game changer for my manufacturing process. The extruder is efficient, easy to operate and built to last. Their customer is excellent and they guided me well through installation and setup. Highly recommended!
NEERAJ CHAUDHARY (NK)
FAQ

Hypoid Gear FAQs

Questions buyers usually ask us before sending an enquiry for hypoid gear.

Should I use a hypoid gear, a spiral bevel gear or a worm drive for a right-angle reducer?

A hypoid gear suits right-angle drives where the shafts are offset and high torque is needed in a compact space. Compared with a spiral bevel pair it allows a larger, stronger pinion, but its teeth slide more. Compared with a worm drive of similar ratio it runs cooler and more efficiently. We review your layout, torque and ratio before recommending one.

What oil does a hypoid gear set need?

Hypoid teeth slide heavily along their length, so they need extreme-pressure gear oil, commonly an API GL-5 hypoid grade. Ordinary gear oil without EP additives can lead to scoring. Run a new set in at reduced load, change the oil afterwards to flush out wear particles, and then check level and condition at regular intervals.

What should I send for a hypoid gear quotation?

Please send the drawing or the worn pinion and wheel, tooth counts, axis offset, spiral hand, shaft angle and mounting distances. Add the input speed, transmitted torque or motor power, operating temperature, the machine and the quantity. Hypoid gear material is typically a case-hardening steel such as 20MnCr5 or EN353, so state any grade your specification requires.

Can you reproduce a hypoid gear set from worn samples?

Yes, but please send both gears. A hypoid pinion runs correctly only with its own matched wheel, so we measure the two together, including tooth counts, offset, spiral angle and hand, and mounting distances. We then make a new matched set, from a single replacement to batch quantities, and check dimensions and runout with dial gauges.

Where do you supply hypoid gears?

We manufacture hypoid gear sets at our unit in Gandevi, Gujarat, and supply industrial users across India for conveyors, lifting machinery, material handling and general engineering. Export orders are accepted under our IEC registration and made to the customer's drawing. We can also advise on the EP lubrication the set will need once installed.

How to order

How We Make Your Hypoid Gears

  1. Send your requirementDrawing, sample or photos of the hypoid gear, with the quantity you need.
  2. Technical check and quoteWe confirm material, hardness and tolerances, then send price and delivery time.
  3. Manufacturing and inspectionMade at our Gandevi unit; dimensions are checked before dispatch.
  4. DispatchPacked for road transport across India, or for export shipment.
Clients

Companies We Supply

Avgol logo
Eveready logo
Akash logo
Santec Group logo
Linit Exports Pvt Ltd logo
Lasons logo
Maredo logo
Hardcarb logo
PAA logo
Prochem logo
Orange logo
ACE Robotics Pvt Ltd logo
Castco logo
BHARAT FORGE logo
Kalyani logo
ARV Engineering logo
Coromandel logo
Bioradmedisys logo
Al tamauez logo
Murugappa logo
Gansons logo
Emami Agrotech Ltd logo
GSW logo
Godrej logo
JSW logo
Bhushan Power & Steel logo
Unicare logo
Centuryply logo
Exide logo
Ha-KO Industries logo

Need Hypoid Gears made to your drawing?

Send the drawing or a sample with the quantity. We supply across India and take export orders.

Call +91-9898059219